CL18-NBD00-SNCR CL series level detection switch
Save to Favorites
Specifications
| Parameter | Value |
|---|---|
| Measurement principle | Capacitive frequency sweep |
| Measurement differential | ±1 mm |
| Media characteristics | DC≥1.5 |
| Response Time | 0.2 s |
| Damping time | 0~5 s (configurable) |
| Repeatability | ±5 mm |
| Operating voltage | 12~30 V DC |
| Startup time | <1 s |
| Operating Current | <50 mA |
| Protection circuit | Reverse polarity protection / short-circuit protection |
| Dielectric withstand voltage | 500 V AC, 50/60 Hz, 1 minute |
| Output Mode | NPN Open Collector |
| Switching mode | NO/NC switchable |
| Voltage drop | NPN:1.5+0.5V, Rload=10k |
| Output Current | <150 mA |
| Leakage current | <100 uA |
| Process pressure | -0.1~10 MPa |
| Process temperature | -40 ℃~115 ℃ (no freezing) |
| Operating Temperature | -40 ℃~85 ℃ (no freezing) |
| Working Humidity | 5 %~95 % RH (no condensation) |
| IP Rating | IP67 |
| Wetted surface roughness | Ra<0.8 μm |
| Wetted material | PEEK |
| Installation position | Top/bottom/side all acceptable |
| Connection Method | M12/4-pin connector |
| Alarm point parameter AL1 | Low dielectric constant medium: 250; water-based medium: 550; conductive slurry: 720; PV≥Wind0: output alarm |
| Measured value PV | 0~800; probe in air: 100; probe in tap water: 800 |
| Alarm differential | 25 |
| Protection function | Parameters cannot be modified before being unlocked |
Datasheet
Supplier Information
Related Products
-
Fiber Bragg Grating Pressure Sensor
Sensors
Xkkb
Fiber Bragg Grating Pressure Sensor
-
Fiber Bragg Grating Pressure Sensor
Sensors
Xkkb
Fiber Bragg Grating Pressure Sensor
-
XNY-T1 Front-Loading Single Sensor (Single Probe)
Sensors
Cdxnyzk
Compared with existing probes, the single-crystal sensor provides good thermal stability and convenient mounting. It installs from the top of the vacuum chamber, with cooling tubes perpendicular to the crystal face. Exposed crystal electrodes are properly grounded to reduce RF interference. Advantages: A front-loading crystal holder provides direct contact without intermediate parts. 4xM5 screws replace the traditional large G 1-inch nut for easy installation; chamber opening is stated as 26.5 and thickness ≤18mm. Enlarged cooling passages prevent inadequate cooling and scale blockage. An imported integrated MICRODOT T0 BNC connector, using a high-temperature Ni-C alloy vacuum process, prevents water-related short circuits. Length and vacuum interfaces can be customized. Repeatedly removable inlet/outlet locking-nut fittings are available, with default 12x8 water tubing.
-
Side Probe
Sensors
Cdxnyzk
Compared with existing probes, the single-crystal sensor provides good thermal stability and convenient mounting. It installs from the top of the vacuum chamber, with cooling tubes perpendicular to the crystal face. Exposed crystal electrodes are properly grounded to reduce RF interference. Advantages: A front-loading crystal holder provides direct contact without intermediate parts. 4xM5 screws replace the traditional large G 1-inch nut for easy installation; chamber opening is stated as 26.5 and thickness ≤18mm. Enlarged cooling passages prevent inadequate cooling and scale blockage. An imported integrated MICRODOT T0 BNC connector, using a high-temperature Ni-C alloy vacuum process, prevents water-related short circuits. Length and vacuum interfaces can be customized. Repeatedly removable inlet/outlet locking-nut fittings are available, with default 12x8 water tubing.
-
Dual Probe
Sensors
Cdxnyzk
Related Articles
As a core precision optical component for wavelength screening, frequency locking and spectral demodulation, optical etalons are widely used in high-end scientific research and precision laser equipment.
As a vital emerging sector of modern three-dimensional spatial economy, the low-altitude economy has become a new global growth driver. It covers a wide range of commercial scenarios, including UAV navigation and obstacle avoidance, precise airspace management, aerial mapping, low-altitude logistics distribution, security monitoring and emergency disaster rescue. Nevertheless, frequent extreme weather, complex terrain obstacles and increasingly dense low-altitude flight activities pose severe challenges to the safety and stability of low-altitude aircraft operations.
Laser pump sources are the core energy input component of solid-state lasers and laser amplifiers, and their performance directly determines the output power, beam quality and service life of the entire laser system. In scenarios such as industrial processing, scientific research experiments and high-end equipment, improper pump source selection will not only result in substandard system performance, but also bring a series of problems such as rapid device degradation and high operation and maintenance costs. This article sorts out the core selection logic and key pitfalls of pump source procurement, and provides selection references based on mature, mass-produced high-reliability products to help purchasers efficiently screen suitable products.
Shandong Haucore Optoelectronics Co., Ltd. introduces the HGLD‑792‑COS‑D‑10WB semiconductor laser within its COS series. Delivering an output power of 10 W at a central wavelength of 792 nm, this device adopts gold‑tin bonding COS packaging. Featuring high reliability and long service life, it serves as a preferred pump source for solid‑state lasers and is widely deployed in industrial processing, laser display, medical & aesthetic treatment, scientific research and other fields.
Loading...
Name
Phone
Organization
Use Case
Database Platform