10GBASE-ER SFP+ 1550nm 40km Hioptel HSFP10-1541 Module

10GBASE-ER SFP+ 1550nm 40km Hioptel HSFP10-1541 Module

Supplier
Hioptel
Category
Transmitters and Receivers
Origin
China

HSFP10-1541 is a 10-Gigabit SFP+ optical module based on a 1550nm cooled EML laser, designed to transmit and receive optical data over single-mode fiber for distances up to 40km. The SFP+ ER is a small form-factor pluggable module for duplex optical data communication, such as 10GBASE-ER/EW as defined by IEEE 802.3ae. Its SFP+ 20-pin connector supports hot plugging. Transmitter inputs and receiver outputs have 100-ohm differential impedance, with internally AC-coupled data lines. Differential termination reduces differential-to-common-mode conversion for high-quality signal termination and low electromagnetic interference. The transmitter converts 10Gbit/s serial PECL or CML electrical data to 10GBASE-ER-compliant serial optical data. An open-collector-compatible transmit-disable pin (Tx_Dis) disables laser transmission at logic 1 or when unconnected; logic 0 enables normal operation. An internal automatic power control (APC) loop maintains constant optical output across supply-voltage and temperature changes. An open-collector-compatible transmit-fault pin (Tx_Fault) is provided. TX_Fault is a module output that goes high when the transmitter detects a laser-operation or safety-related fault. This open-drain/collector output should be pulled up to Vcc_Host through a 4.7-10 kΩ resistor at the host. TX_Disable is a module input: high or floating disables the SFP+ transmitter output. Pull this pin up to VccT through a 4.7 kΩ to 10 kΩ resistor.

Specification Snapshot
Operating Temperature
0~+70 °C
Request a Quote Download Datasheet
Save to Favorites Save to Favorites

Overview

HSFP10-1541 is a 10-Gigabit SFP+ optical module based on a 1550nm cooled EML laser, designed to transmit and receive optical data over single-mode fiber for distances up to 40km. The SFP+ ER is a small form-factor pluggable module for duplex optical data communication, such as 10GBASE-ER/EW as defined by IEEE 802.3ae. Its SFP+ 20-pin connector supports hot plugging. Transmitter inputs and receiver outputs have 100-ohm differential impedance, with internally AC-coupled data lines. Differential termination reduces differential-to-common-mode conversion for high-quality signal termination and low electromagnetic interference. The transmitter converts 10Gbit/s serial PECL or CML electrical data to 10GBASE-ER-compliant serial optical data. An open-collector-compatible transmit-disable pin (Tx_Dis) disables laser transmission at logic 1 or when unconnected; logic 0 enables normal operation. An internal automatic power control (APC) loop maintains constant optical output across supply-voltage and temperature changes. An open-collector-compatible transmit-fault pin (Tx_Fault) is provided. TX_Fault is a module output that goes high when the transmitter detects a laser-operation or safety-related fault. This open-drain/collector output should be pulled up to Vcc_Host through a 4.7-10 kΩ resistor at the host. TX_Disable is a module input: high or floating disables the SFP+ transmitter output. Pull this pin up to VccT through a 4.7 kΩ to 10 kΩ resistor.

Specifications

ParameterValue
Launcher input and receiver output resistance100 欧姆
Launcher1550 nm cooling EML
Launch disabled Tx_Dis [Disable laser launch]Logic "1" or not connected
Launch disabled Tx_Dis [Normal work]Logical "0"
TX_Fault [Module launchers detected malfunctions related to laser operation or safety]High level of electrons
TX_Fault [Output Contact]Leaking/enabled poles
Electrical resistance [TX Fault / Drop Up to HostVcc Host]4.7-10 kΩ
Electrical resistance [TX Disable / Up to VccT]4.7 kΩ to 10 kΩ
Serial light interface [802.3 ae 10GBASE-ER/EW]10 Gb/s
Transmission Distance [Over 9/125μm single-mode fiber]Kanda 40km
PackageSFP+ MSA
ConnectorDouble-job LC
Interface [For management and diagnostic surveillance]Line 2
High-speed electrical interfaceSFI
Single power supply+3.3 V
Power ConsumptionLess than 1.5 W
Operating Temperature0~+70 °C
Boot connector20 引脚

Applications

• 10G Base-ER/EW • 10G fibre-optic channel (with/without FEC) • 10G storage system

Key Features

Hot-pluggable. 10Gb/s serial optical interface to 802.3ae 10GBASE-ER/EW.1550nm cooled EML transmitter with TEC and PIN photodetector; up to40km over9/125μm SMF. SFP+ MSA with duplex LC; two-wire management/diagnostic interface; SFI high-speed electrical interface; very low EMI and strong ESD protection. Single+3.3V supply; power below1.5W; temperature0~+70°C. Complies with SFP+ SFF-8431/SFF-8432,SFF-8472 Rev10.2,IEEE 802.3ae 10GBASE-ER/10GBASE-EW,IEC 60825-1 Class 1 eye-safety and RoHS.

Datasheet

Please provide your email to download the datasheet.

Your name
Email Address

Invalid email format. Please try again.

Send Request

Supplier Information

Hi
Hioptel
View Supplier →
Shenzhen Hi-Optel Technology Co., Ltd. (hereinafter referred to as "Hi-Optel") was established in May 1999 and is a pioneer in China's core optical communication optical module field and a mainstream high-end optical device manufacturer. The company has a registered capital of 100 million yuan, total assets of over 300 million yuan, more than 450 employees, and modern factory buildings of over 10,000 square meters. The company was officially listed on the National Equities Exchange and Quotations on May 18, 2015, with stock code: 832449, opening a new chapter in capitalization development. Relying on advanced TO components, COB packaging technology, and intelligent production lines covering the full range of optical transceivers from 155M to 800G, Hi-Optel is committed to providing global customers with cost-effective and highly reliable active optical transceiver solutions. Products are widely used in key areas such as telecommunications networks, data centers, and artificial intelligence computing centers. The company has built and continuously improved a comprehensive quality management system, and has obtained ISO 9001 quality management system certification, ISO 14001 environmental management system certification, ISO 45001 occupational health and safety management system certification, TL9000 telecommunications industry quality management system certification, and ESD protection system certification. All products comply with RoHS environmental standards and support international certifications such as CE, UL, TUV, KCC, and FDA, ensuring product compliance and competitiveness in the global market. As a national high-tech enterprise and a specialized and sophisticated "little giant" enterprise, Hi-Optel has two provincial-level engineering technology research centers and has established a market-oriented R&D system with independent innovation as the core. The R&D team brings together high-end industry talents, has won more than 80 patents, and has undertaken multiple major scientific research projects from the National Development and Reform Commission, the Ministry of Science and Technology, and the Shenzhen Municipal Government. The company is based in China and radiates globally. It has established a bonded factory in Malaysia to achieve overseas localized production and efficient delivery, supplemented by a global sales and technical support network to provide customers with agile, reliable, and customized supply chain assurance and service support. Hi-Optel always adheres to the business philosophy of "integrity, responsibility, and win-win", and insists on open collaboration and win-win development. Its "Hi-Optel" brand optical devices and optical transceiver products have won market trust with excellent performance. The company also provides technical collaboration and OEM/ODM services for internationally renowned enterprises, continuously empowering customer value and building the future of the industry through technological breakthroughs, product innovation, and business model evolution.

Request a Quote

Our team responds within 24–48 hours
10GBASE-ER SFP+ 1550nm 40km Hioptel HSFP10-1541 Module
Hioptel · Transmitters and Receivers
Direct from Manufacturer
Your inquiry will be sent directly to the manufacturer
Photonics Source Platform
We handles the inquiry on your behalf
Your information is protected and will never be shared without consent.
Contact Us

Loading...

GetExperimental Plan

Name

Phone

+86

Organization

Use Case

AI Parametric Selection
Smart Match · Precise Recs
Enter Specifications
AI Smart Matching
Get Best Matches
Skip Manual Comparison
Find Best Solutions Fast
Select Now →