HVSW-04 High-Voltage High-Repetition-Rate Pockels Cell Drivers HVSW-04-2kV-WR
HVSW-04 is a dedicated high-voltage, high-repetition-rate Pockels cell driver for picosecond and femtosecond lasers, primarily for extracting individual pulses from a pulse train. The driver offers two operating modes. Modified versions also provide continuously adjustable pulse width over 15-2000ns. It requires a +24 V DC supply, a pulse generator to set operating frequency and pulse width in variable-width mode, and a bipolar HV DC supply such as HVPS-300. The user sets output voltage through the high-voltage DC supply interface. Maximum output voltage is 4 kV bipolar; maximum repetition rate is 0.5-4 MHz depending on output voltage. Operating modes: fixed-width short pulses of approximately 15-20 ns, triggered by the leading edge of an external TTL signal; variable-width long pulses, normally adjustable over 100-2000 ns with other ranges available on request, where the external TTL leading edge raises the pulse and its trailing edge lowers it. Original target-performance table: Output voltage, kV | repetition rate, MHz (*) | power consumption, W. 4.0 | 0.5 | < 300; 3.2 | 1 | < 400; 2.0 | 2 | < 300; 1.6 | 3 | < 300; 1.4 | 4 | < 350. (*) Values are approximate; actual performance depends on load capacitance and cooling. Bipolar output pulse voltage U is formed by applying +U/2 to one output wire and –U/2 to the other. Both output poles are therefore below HV. The water-cooled driver is controlled through either an analog interface or RS-485, not simultaneously. PC software is available for laboratory use. Common models (original table): HVSW-04 or HVSW-04-4kV | output voltage up to 4.0kV; repetition rate up to 1MHz at 3.2kV; rise/fall time 9-11ns at 4kV; short pulses 15-20ns fixed and long pulses 100-2000ns adjustable; the 20-100ns range is unavailable. HVSW-04-2kV | output voltage up to 2.0kV; repetition rate up to 4MHz at 1.6kV; rise/fall time 7-9 ns at 2kV; short pulses 15-20ns fixed and long pulses 100-2000ns adjustable; the 20-100ns range is unavailable. HVSW-04-4kV-WR (wide range) | output voltage up to 4.0kV; repetition rate up to 1MHz at 3.2kV; rise/fall time 9-11ns at 4kV; continuously adjustable pulse width over 15-2000ns. HVSW-04-2kV-WR (wide range) | output voltage up to 2.0kV; repetition rate up to 4MHz at 1.6kV; rise/fall time 7-9ns at 2kV; continuously adjustable pulse width over 15-2000ns.
Save to Favorites
Overview
Specifications
| Parameter | Value |
|---|---|
| Low-Voltage Input | +24VDC， maximum 2.5A |
| High-Voltage Input | +HV/2 on one wire; -HV/2 on the other wire |
| Output Type | Bipolar |
| Pulse Amplitude | Adjustable ， up to 4kV |
| Voltage Baseline | Fixed, 0 V |
| Maximum Repetition Rate | up to 4MHz |
| Minimum Repetition Rate | Single shot |
| Pulse Width - Fixed Pulse Width Mode - Variable Pulse Width Mode | 15-20ns, fixed; 15-2000ns or 100-2000ns, adjustable |
| Pulse Interval | >50ns |
| Rise/Fall Time | From 5-7ns at an output voltage of ~1kV to 9-11ns at maximum. Voltage (4kV) |
| Delay Time | <50ns |
| Jitter | <0.5ns (±250ps) |
| Load Capacitance | typical:typical 5-7 pF |
| Operating Temperature | +10~+40℃ |
| Storage Temperature | -20~+60℃ |
| Humidity [Non-condensing] | 0~90%, non-condensing |
| Protection | - Ultralong pulse adjustable within 200ns-2200ns (threshold); - Overtemperature protection |
| Dimensions | 176 mm × 69 mm × 50 mm |
| Weight | <0.5kg |
Applications
Key Features
Datasheet
Please provide your email to download the datasheet.
Invalid email format. Please try again.
Supplier Information
Related Products
-
1CH×25G/28G DML Driver
Software and Data Services
Xy-technology
XY5221DD is One. Single Channel Laser Driver ， Designed for direct modems 25Gb/s Laser Interface 。 The currents and the transients can be replaced by the currents. 2 Line Line Lines Interface Independent Programming ， Meanwhile... 2 Line Interface Supports also the inclusion of programmability for balancing and cross-point adjustments ， Take one. Tx Disable ， It can be closed. Laser Erosion and Moderation Current ， Existing IBIAS Monitor 。 This simulation output can be used to Laser Overcrowding and / or Laser Modulation Current for External Monitoring 。 There's a piece in there. ADC Functions ， It can be used for foot-inducing measurements via electrical input of a special back-cover monitor TX_PWR。ADC It can also be configured for measurement. VCC（ ..can measure each Power Supply ） and IBIAS（ Average Laser Erosion of currents ）。
-
1CH×25G/28G EML Driver
Software and Data Services
Xy-technology
XY5221E is A high-performance piece. Single Channel 28Gbps EML Driver 。 It provides daring. 30GHz High bandwidth and greater than 2.5Vpp and the output range ， The cost of the operation is about 0.17W。 It's designed for use in... Drive EML Laser ， The chip is available in nudity chip form. 。
-
4CH×25G/28G DML Driver
Software and Data Services
Xy-technology
XY5224DD is One. Four Channel Laser Driver ， Designed for direct modems 25Gb/s Laser Interface 。 The currents and the transients can be replaced by the currents. 2 Line Line Lines Interface Independent Programming ， Meanwhile... 2 Line Interface Supports also the inclusion of programmability for balancing and cross-point adjustments ， Take one. Tx Disable ， It can be closed. Laser Erosion and Moderation Current ， Existing IBIAS Monitor 。 This simulation output can be used to Laser Overcrowding and / or Laser Modulation Current for External Monitoring 。 There's a piece in there. ADC Functions ， It can be used for foot-inducing measurements via electrical input of a special back-cover monitor TX_PWR。ADC It can also be configured for measurement. VCC（ ..can measure each Power Supply ） and IBIAS（ Average Laser Erosion of currents ）。
-
4CH×25G/28G EML Driver
Software and Data Services
Xy-technology
XY5224E is A high-performance piece. Four Channel 28Gbps EML Driver 。 It provides daring. 30GHz High bandwidth and greater than 2.5Vpp and the output range ， The cost of the operation is about 0.45W。 It's designed for use in... Drive EML Laser ， The chip is available in nudity chip form. 。
-
25G/28G CDR+VCSEL Driver
Software and Data Services
Xy-technology
XY5921V Integration VCSEL Driver 、 Balancer and clock data recovery 。 None The reference clock will support it. 24.3Gbps Present. 28.1Gbps Rate range ， It's also possible. bypass Mode supports lower rate 。 The chip is provided in nudist form. 。
Related Articles
As a professional ultraviolet‑laser solution provider, Precilasers has launched its 266 nm narrow‑linewidth industrial laser, delivering reliable single‑frequency output for high‑precision interference lithography, semiconductor inspection and precision metrology applications.
On November 28, 2024, the 3rd China Laser Star Enterprise Summit & Advanced Laser Processing Technology Summit, an annual influential event in the laser industry, was grandly held in Wuhan Optics Valley.
Within cutting‑edge ultrafast photonics research, asynchronous optical sampling (ASOPS) and synchronous sampling serve as fundamental technologies for terahertz excitation detection, coherent Raman imaging and other time‑resolved spectroscopy experiments.
A laser bar is an array semiconductor laser chip integrated with dozens of emitters, which realizes hundred-watt quasi-continuous output on a single chip. With regular emitter arrangement and controllable fill factor, integrated thermal design and superior wall-plug efficiency compared to single chips, it acts as the core light source for high-power pumping, medical lasers and precision processing.
Loading...
Name
Phone
Organization
Use Case
Database Platform