Stepper Motor Actuator DPP6
JCOPTIX electric actuators replace screws/micrometers on manual mounts and stages. Miniature 2-phase 2-pole stepper motors provide smooth precision linear motion with stable 3 μm minimum increments throughout travel. Available travel is 6 mm or 13 mm. The 6 mm version mounts by Ø6 mm smooth shaft or M6 × 0.25 threads; the 13 mm version has an Ø9.5 mm smooth mounting shaft. Stepper actuators, 6 mm travel. Models: DPP6, DPP6A. Travel 6 mm; translating nonrotating tips; manual socket for 3 mm key; threaded or smooth-shaft mounting. JCOPTIX 6 mm actuators are smooth and compact, with fully retracted lengths 72.5 mm for DPP6 and 60.3 mm for DPP6A. Miniature 2-phase 2-pole motors reach 2 mm/s. Nonrotating tips reduce friction/wear and improve smoothness. When unpowered, a rear 3mm socket permits manual adjustment; noticeable resistance means the mechanical limit, beyond which movement must stop. Never adjust manually while powered, as motor damage can result. Thrust is 40 N and minimum step 3 μm throughout travel. Acceleration/deceleration is slightly louder than constant speed without affecting use/accuracy. DPP6 replaces M6 × 0.25 adjusters on Ø25.4 mm and Ø50.8 mm mounts. After homing, screw it into the mount until the front plate lifts, then secure with the copper nut. DPP6A fits products with 6 mm smooth mounting bores and can fit 6.5 mm-travel linear stages; contact support for installation. Built-in calibration files with DCP-201C provide bidirectional repeatability ≤±2.5 μm and homing accuracy ±2.5 μm. Stage-stored calibration data allow any DCP-201C to maintain calibrated accuracy. No hot-plugging or manual adjustment while powered; either can damage the motor. Avoid speeds 0.2 ±0.05 mm/s and 0.4 ±0.05 mm/s because low-speed motor behavior increases vibration and may cause motion error. Stepper actuator, 13 mm travel. Model: DPP13. Travel 13 mm; translating nonrotating tip; manual socket for 3 mm key; smooth-shaft mounting. This JCOPTIX 13 mm actuator is compact and smooth, with fully retracted length 68.6 mm. A miniature 2-phase 2-pole motor reaches 2 mm/s. Nonrotating tips reduce friction/wear and improve smoothness. Unpowered, a rear 3 mm socket allows manual adjustment. Stop at noticeable resistance indicating the mechanical limit; never adjust while powered because motor damage can result. Thrust is 40 N and minimum step 3 μm throughout travel. Acceleration/deceleration is slightly louder than constant speed without affecting use/accuracy. DPP13 replaces 13 mm micrometers with Ø9.5 mm mounting shafts. It can fit 13 mm-travel linear stages; contact support. Built-in calibration files with DCP-201C provide bidirectional repeatability ≤±2.5 μm and homing accuracy ±2.5 μm. Stage-stored calibration lets any DCP-201C maintain calibrated accuracy. No hot-plugging or powered manual adjustment; both can damage the motor. Avoid 0.2 ±0.05 mm/s and 0.4 ±0.05 mm/s because low-speed vibration may increase and cause errors.
Save to Favorites
Overview
Specifications
| Parameter | Value |
|---|---|
| Motor type | 2-Phase 2-Pole Stepper Motor |
| Travel | 6 mm |
| Bidirectional positioning repeatability | ±2.5 μm |
| Homing Accuracy | ±2.5 μm |
| Backlash | <15 μm |
| Maximum thrust | 40 N |
| Maximum Speed | 2 mm/s |
| Maximum Acceleration | 10 mm/s² |
| Minimum Repeatable Incrementᵃ | 3 μm |
| Theoretical Resolutionᵇ | 3.7 nm |
| Cable length | 0.6 m |
| Mounting Method | M6 × 0.25 Threaded Mounting |
| Operating Temperature | 5~40 ℃ |
| Connector Type | DB15 |
Key Features
Datasheet
Please provide your email to download the datasheet.
Invalid email format. Please try again.
Supplier Information
Related Products
-
Electric Servo CNC Press Brake Machine 15T650
Motors and Drives
Auroralaser
Bending Capacity: 150 kN Bending Length: 650 mm Distance Between Columns: 300 mm
The Electric Servo Press Brake utilizes a fully electric servo drive system for zero standby consumption and rapid response. It delivers high-precision bending with quiet operation, significantly improving energy efficiency and productivity.
-
Electric Servo CNC Press Brake Machine 30T1050
Motors and Drives
Auroralaser
Bending Capacity: 300 kN Bending Length: 1050 mm Distance Between Columns: 800 mm
The Electric Servo Press Brake utilizes a fully electric servo drive system for zero standby consumption and rapid response. It delivers high-precision bending with quiet operation, significantly improving energy efficiency and productivity.
-
Electric Servo CNC Press Brake Machine 40T1500
Motors and Drives
Auroralaser
Bending Capacity: 400 kN Bending Length: 1500 mm Distance Between Columns: 1200 mm
The Electric Servo Press Brake utilizes a fully electric servo drive system for zero standby consumption and rapid response. It delivers high-precision bending with quiet operation, significantly improving energy efficiency and productivity.
-
Electric Servo CNC Press Brake Machine 60T1500
Motors and Drives
Auroralaser
Bending Capacity: 600 kN Bending Length: 1500 mm Distance Between Columns: 1200 mm
The Electric Servo Press Brake utilizes a fully electric servo drive system for zero standby consumption and rapid response. It delivers high-precision bending with quiet operation, significantly improving energy efficiency and productivity.
-
Electric Servo CNC Press Brake Machine 60T2000
Motors and Drives
Auroralaser
Bending Capacity: 600 kN Bending Length: 1500 mm Distance Between Columns: 1200 mm
The Electric Servo Press Brake utilizes a fully electric servo drive system for zero standby consumption and rapid response. It delivers high-precision bending with quiet operation, significantly improving energy efficiency and productivity.
Related Articles
Against the evolving demands for military‑grade hardware, rail transit equipment and heavy‑duty machinery that run under high‑shock vibrating conditions, anti‑loose connectors serve as indispensable hardware for stable power delivery and high‑speed signal transmission.
Developed by RealLight (Beijing), the R7M high‑power diode laser module belongs to the AW multi‑functional laser product family.
GYOPTICS 30 W collimated isolator is a highly‑reliable passive optical component optimized for 1064 nm high‑power laser systems. Characterized by low insertion loss and superior backward‑light suppression capability, it effectively blocks reflected light traveling back toward the laser resonator, eliminating back‑reflection‑induced instability and protecting fiber or solid‑state laser sources during long‑term operation.
Santec introduces the HSL‑20‑C‑E swept laser. Built on proprietary MEMS technology, this compact integrated light source combines high‑speed scanning and long coherence length, optimized for SS‑OCT imaging systems. Configurable start trigger and k‑clock outputs are available to meet development requirements for medical‑biological imaging and industrial non‑destructive inspection equipment.
Loading...
Name
Phone
Organization
Use Case
Database Platform